Search found 2400 matches

by MickeyMoto
18 Mar 2024 07:20
Forum: Tre e mezzo
Topic: Lighting circuit problem
Replies: 3
Views: 78

Re: Lighting circuit problem

If you read the blue book there is a section on fault finding the charging circuit. I would say that 12.5 volts across the battery at 5k rpm is a bit low. Your regulator may be faulty.

You may want to check the earthing points, too.
by MickeyMoto
17 Mar 2024 16:37
Forum: Tre e mezzo
Topic: Best 31/2 cam for all-round flexibility?
Replies: 19
Views: 1323

Re: Best 31/2 cam for all-round flexibility?

Thank you, Norbert.
by MickeyMoto
17 Mar 2024 09:07
Forum: Tre e mezzo
Topic: Best 31/2 cam for all-round flexibility?
Replies: 19
Views: 1323

Re: Best 31/2 cam for all-round flexibility?

This is good info.

A Sport piston with a Strada cam is a good option.

I know the 501 nikisil barrels do not fit an500 crankcase, but do the 350 nikisil barrels fit an earlier 350 crankcase?
by MickeyMoto
03 Mar 2024 10:31
Forum: Tre e mezzo
Topic: Best 31/2 cam for all-round flexibility?
Replies: 19
Views: 1323

Re: Best 31/2 cam for all-round flexibility?

Sport cam was used from the first sports up until the later K series bikes where they moved to the M cam. There should be an S Stamped in the cam between the middle lobes, not so helpful if the engine is together, but easy to check what cam you have by measuring with a timing disc. None of the Mori...
by MickeyMoto
29 Feb 2024 18:58
Forum: Tre e mezzo
Topic: Reinstating the electric starter part 2
Replies: 9
Views: 403

Re: Reinstating the electric starter part 2

I would not think Morini could afford a different casing.

Has the linkage been changed, do you have rear sets?

Of course, I could be wrong, not unknown!
by MickeyMoto
24 Feb 2024 08:43
Forum: Tre e mezzo
Topic: Engine woodruff Keys puzzler
Replies: 3
Views: 311

Re: Primary Drive woodruff Key puzzler

I think I have a spare key, if needed.
by MickeyMoto
22 Feb 2024 08:32
Forum: Singles
Topic: 250 anybody?
Replies: 3
Views: 333

Re: 250 anybody?

This one is a bit sad. The provenance is rather lacking. I could understand if it were the bike that came second in the World Championships.
by MickeyMoto
17 Feb 2024 11:35
Forum: Tre e mezzo
Topic: Bottom end strip
Replies: 4
Views: 421

Re: Bottom end strip

Hi, 1. The nuts should be recessed in nut shaped holes. 2. You will probably need to drill out the crankshaft bolts if they do not yield. No idea from where they can be obtained. Re use the old ones if not damaged. 3. Use the special tools, the nut is ft (fantastically tight!). Butchering a socket w...
by MickeyMoto
16 Feb 2024 08:56
Forum: Tre e mezzo
Topic: Oil pump seal variation in sizes/mdina part different?
Replies: 4
Views: 401

Re: Oil pump seal variation in sizes/mdina part different?

I have used the black one but I prefer the old green one. Check the green one carefully, obviously not worth the risk if it is worn.
by MickeyMoto
13 Feb 2024 12:52
Forum: Singles
Topic: 250 anybody?
Replies: 3
Views: 333

250 anybody?

Does this increase the value of my Morini? A 250 single going for a ridiculous price, whatever next?

https://www.motorcyclenews.com/news/202 ... n-results/
by MickeyMoto
08 Feb 2024 10:43
Forum: Bikes and bits wanted
Topic: Morini 501 engine wanted
Replies: 10
Views: 608

Re: Morini 501 engine wanted

Carts wrote: 07 Feb 2024 19:48 Hi Mickey

Thanks for the advice, any ideas how to look for an engine in Spain.
They sometimes turn up on Car and Classic.
by MickeyMoto
07 Feb 2024 17:43
Forum: Bikes and bits wanted
Topic: Morini 501 engine wanted
Replies: 10
Views: 608

Re: Morini 501 engine wanted

Don't discount importing an Excalibur from Spain, if you see one.
by MickeyMoto
30 Jan 2024 08:26
Forum: Tre e mezzo
Topic: Best 31/2 cam for all-round flexibility?
Replies: 19
Views: 1323

Re: Best 31/2 cam for all-round flexibility?

The Excretia had a J cam. The 501 with a J cam is a torquey beast but it starts getting wheezy at the top end. My 501 would pull well from 30 mph in 6th gear.
by MickeyMoto
29 Jan 2024 14:22
Forum: Tre e mezzo
Topic: Instrument bezels and glass
Replies: 14
Views: 1072

Re: Instrument bezels and glass

Ok, i will look at the 80mm rings.

I do have a plan to clamp the bezel!
by MickeyMoto
29 Jan 2024 08:20
Forum: Tre e mezzo
Topic: Instrument bezels and glass
Replies: 14
Views: 1072

Re: Instrument bezels and glass

Hello, Ooh, that sounds useful. I have an idea of how to do it but a tool for the job would be better. Just need to sneak out to the garage to have a look. The rubber seal is intact, but it looks like it does a few jobs like hold the glass and seals around the edge of the instrument. The only place ...