MRC Forum- brought to you by www.morini-riders-club.com

Here are the SURFLEX kit part numbers with MM parts in brackets, you can check with vendor Full set: S 1149 Serie composta da: 5 articolo 2 M 77 (20.01.25) 1 articolo 62 M 39 (20.01.24) 4 articolo 62 M 43 (20.01.26) 1 articolo 2 M 131 (20.01.32) driving plate set (fibre composites) S 1149/B Serie co...

bad luck Terry although if it was turning it may have been of limited use returning to my query about clutch plates - these are advertised on fleabay but the 500 sport is pretty much the only one not listed. Just to be on the safe side - can I be certain they will fit? https://www.ebay.co.uk/itm/26...

Congratulations to you and Miss Amy well done!
Mark

John Great initiative message Tom MRC chairman and Chris MRC products. We are considering a number of items that are unobtainable. Whether we go ahead and make these ourselves or facilitate others through supplier or supply chain depends on many things. Present projects include full set Dart panels ...

Hello Richard 30.01.61 is same part on Kanguro X, airbox side. The coupling ring is just a hard plastic stiffener thing - you can 3D print that! I can measure one for you if needed if no one has them. The 250 2C uses the two right angle parts coupled together, using the stiffener ring- bingo! replac...

72degrees wrote: ↑08 Nov 2023 19:13 Still want a single

A small Morini 350/400 may make sense, like Triumph etc, but so far nothing like this has been shown on any factory roadmap.

You can ask Alberto Monni on his views of a the market? He receives our magazine.

Mark

MickeyMoto wrote: ↑08 Nov 2023 10:02 A 750 v twin!

In Alberto Monni's (general manager) interviews with Moto.it it is said that the engine was designed in Italy by Morini's engineers.
I rather assumed that Morini would buy in a proven engine?
Notice Massimo Gustato R&D manager is present in some videos

Mark

https://www.youtube.com/watch?v=INhWeap1B6Y points from the video Fragile and dangerous rear number plate holder/hugger has been removed, hurrah, and replaced with a proper rear number plate Oil Cooler Different swinging arm Euro 5+ More pillion friendly seat Ok so we can say Chinese this and Chines...

And Milano 1200, incredible 5 new models at the show.

https://www.youtube.com/watch?v=INhWeap1B6Y
for bagger and Milano

https://www.youtube.com/watch?v=FiOxDfhEJVQ
X-cape 1200

https://www.youtube.com/watch?v=MRpisQ71JfI
Corsaro 750 naked and sport

Hi David,

No it wont fit a 478cc, but you can get edge composites to copy a 500 one, if you don't have one someone may be able to lend you one.

https://www.edgecompositesuk.com

Mark

It definitely good to check the brakes for these kind of issues especially now most of these in the UK are no longer subject to an annual inspection. The sizes are as follows The homolgation A/1 etc define the brake dimensions for Standard machines. Rear drum cast wheel A/3 and K sport or Strada are...

Hi Richard Thanks for the translation, your translation is way better than the official English translation (i have a copy of this) from the 80s :D :D :D Richard, Welcome to the forum, The gasket set from Mdina, for Dell Orto, covers multiple carbs and potentially contains o-rings and seals not need...

Hi Hombre, The 6 pole has two positions in which key can be removed (OFF and PARKING LIGHTS) , the five pole has only one position (OFF) in which the key can be removed. To make it work if its possible but the key could fall out when you put the switch to lights on! Unfortunately the green and blue ...

>Benjy Straw reckons 350 head gaskets will be ok. Once running carbon build up will fill the slight space. I rely on his expertise. Yes I don't see why not, fairly sure all other dimensions are otherwise the same, its only 3mm, or 1.5mm each side oversize, likely will coke up pretty quickly? Mark

The 2 marking is for oversize, meaning 0.2mm or first oversize, measurements would confirm this.

I reckon the dots were made by a "mechanic" to keep parts together as Steve says.

Mark